Serving the Boston area  ·  (857) 465-5405  ·  Open Mon-Sun 7am-7pm
📞 (857) 465-5405 Free Quote

Metal Roofing in Everett, MA (02149) · Local Professionals

Boston Metal Roofing · Fast response in Everett and the Boston area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+318Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Everett is a small, dense city where the housing stock tells its own story: triple-deckers and two-families from the 1890s to the 1920s sit on tight lots, many with low-slope or shallow-pitch roofs that have seen decades of nor'easters and freeze-thaw cycles. Just minutes from the Mystic River and Encore Boston Harbor, these homes face salt air, heavy snow loads, and summer storms that test every seam and fastener.

That's why homeowners in Everett (02149) call Boston Metal Roofing. We know the older two-families and small commercial buildings along Broadway and lower Ferry Street, and we understand how weathered flat and low-slope roofs here need real solutions, not quick patches. Our insured crews specialize in metal roof replacement and commercial metal roofing, and we're based right in Boston, so we're never far away.

Metal Roofing in Everett (02149)

Everett's terrain is a mix of glacial till and urban fill, with tight lots that leave little room for staging materials. Many properties have granite ledge close to the surface, which can affect drainage and make proper flashing and gutter design critical. The city's older two-families and small commercial buildings often have flat or low-slope roofs that are prone to ponding water and ice dams at the eaves. We see a lot of failed fasteners and separated seams on these roofs, especially after nor'easters drive rain sideways. Our team is experienced with the specific challenges of Everett: limited access, historic building stock, and the need to coordinate with neighbors when scaffolding or materials spill over property lines.

We've worked on metal roofs throughout Boston and surrounding areas, from standing seam on Dorchester triple-deckers to copper bay windows in the South End. In Everett, we've replaced low-slope roofs on two-families near Glendale Park and repaired storm damage on commercial buildings off Route 16. We know the local building department's permit thresholds and inspection requirements, and we can help you navigate them.

Our services in Everett

How a Job Works in Everett

Step 1: Call us at (857) 465-5405 or request a free estimate online. We'll schedule an on-site assessment at your Everett property, where we'll inspect your current roof, discuss your options, and provide a detailed written estimate. We'll also check for any permit requirements with the city.

Step 2: Once you approve the estimate, we'll schedule the work. On tight Everett lots, we plan material deliveries carefully to avoid blocking driveways or streets. If your property is in a historic district or has HOA design rules, we'll help you get the necessary approvals. Our crews are fully insured and follow all safety protocols. We'll keep you informed throughout the project.

Step 3: After installation, we clean up thoroughly, haul away all debris, and do a final walkthrough with you to ensure you're satisfied. We leave your property clean and your new metal roof ready to protect your home for decades.

Metal roofing costs in Everett depend on the size and complexity of your roof, the material you choose, and the condition of the existing structure. For a typical Everett two-family with a low-slope roof, metal roof replacement might start around $9 per square foot, while standing seam runs from $10 per square foot. If you're considering a retrofit over existing shingles, that starts at $7 per square foot, but keep in mind that local codes limit the number of layers you can add. Smaller jobs like metal roof repair or leak repair start at $450, and screw replacement or re-fastening starts at $750. We also offer free estimates for commercial and agricultural metal roofing. Call us at (857) 465-5405 to get a precise quote for your Everett property.

My triple-decker near Glendale Park has a low-slope roof that leaks every winter. Can a metal roof fix that?
Yes, a properly installed metal roof can solve recurring leaks on low-slope roofs. We often recommend standing seam or exposed-fastener panels with a continuous underlayment and careful flashing at transitions. The key is addressing ice damming at the eaves, which is common on Everett's older homes. We'll assess your roof's pitch and drainage and recommend a system that handles snow and rain.
A nor'easter just peeled back some panels on my commercial building off Route 16. How quickly can you respond?
We prioritize storm damage emergencies in Everett. Call us at (857) 465-5405 and we'll schedule an inspection as soon as possible, often within 24 to 48 hours. We can tarp or secure the roof to prevent further damage and provide a detailed repair estimate. Our team is fully insured and experienced with insurance claim documentation.
What's the typical cost to replace a metal roof on a two-family in Everett?
For a standard two-family with about 1,500 square feet of roof area, metal roof replacement typically ranges from $13,500 to $20,000, depending on material and complexity. Standing seam costs more, starting around $10 per square foot, while corrugated panels start at $5.50 per square foot. Factors like roof access, existing layers, and flashing details affect the final price. We provide free estimates.
Do I need a permit to replace my roof in Everett, and how long does it take?
Yes, a building permit is generally required for a full roof replacement in Everett. The exact requirements and fees vary, so we recommend checking with the Everett Building Department. We can help you navigate the permit process and schedule inspections. Permit approval typically takes a few days to a couple of weeks, depending on the scope.
My neighbor's tree hangs over my roof, and I'm worried about property lines when installing a metal roof. What should I do?
It's wise to address property line concerns before work begins. We'll review your property survey and coordinate with you on staging and access. If branches overhang, we may need to trim them (with your permission) to prevent damage. For HOA or historic district rules, we can help you get approval for panel profiles and colors. We always respect neighbor boundaries.
Are you fully insured for roofing work in Everett?
Yes, Boston Metal Roofing is fully insured with general liability and workers' compensation coverage. You can have peace of mind knowing our crew is protected and your property is covered.
What maintenance does a metal roof need in Everett's climate?
In Everett, metal roofs benefit from annual inspections, especially after winter. Check for loose fasteners, debris in gutters, and any signs of corrosion near salt air exposure. We recommend cleaning gutters twice a year and touching up scratches. Snow guards can help prevent avalanches on steep roofs. Our team offers maintenance plans to keep your roof in top shape.
Why choose us?

Trusted professionals in Boston

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Boston

All your work handled by qualified professionals in Boston

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

318+ Verified Client Reviews in Boston

⭐⭐⭐⭐⭐ 4.9/5 · 318 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Boston · Response within 24h · No commitment · ☎ (857) 465-5405

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Boston ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm